IEC 62133-2 High Acceleration Shock Test System For Batteries
Mechanical Shock Test
Product Information:
It is required by IEC 62133-2:2017 clause 7.3.8.2, IEC 60335-2-25
Annex BB, YD/T 2344.1 and etc.
This machine is mainly suitable for the impact resistant test of
electronic products, aerospace, ships, military, automobile parts,
transportation and other fields. By selecting different waveform
generators, impact tests of half sine wave, back peak sawtooth wave
or square wave can be carried out.
It meets MIL-STD-202F, IEC-68-2-27, MIL-STD-810F, MIL-STD-883E and
etc.
Device Performance:
- Impact machine mainly introduced
1. Working platform: high strength imported aluminum alloy working
platform.
2. Lifting mechanism: motor drives ball screw to lift the working
platform.
3. Lifting height control: the lifting height is measured by the
photoelectric encoder component installed on the base. The
photoelectric encoder has high precision, strong anti-interference
ability and high reliability to ensure the impact repeatability.
4. Brake system: using pneumatic brake and strong friction brake to
prevent secondary impact braking function, to prevent secondary
rebound
5. Buffer system: effectively reduce the impact of impact test on
the ground, a self-buffer system is designed, which is composed of
base, damper and air bag.
Half sine wave generator is mainly made of engineering rubber or
wool felt. It consists of a variety of different thicknesses
connected in series, forming a variety of stiffness, to achieve
different impact pulse width.
Emergency stop switch: It can cut off the circuit under emergency
circumstances by forcibly disconnecting the contact welding of the
action mechanism.
- Introduction and characteristics of impact measurement system
The system conforms to MIL-STD-810 and IEC68-2-27 standards. It has
accurate and fast impact waveform capture capability, with the
highest sampling rate up to 1MHz. You do not need to worry about
even narrow impact events being missed.
It is also an integrated solution, you don't have to much busy to
view and record, it can capture the impact event to generate a
report shall be complete, more importantly, it also provides the
function of shock response spectrum (SRS), can help you for shock
pulse potential damage for effective evaluation of actual system.
Finally, auxiliary analysis of force deformation, impact response
and so on can help you understand the impact results in more
detail.
Technical Parameters:
| Working platform | 200 × 250 mm |
| Working platform Material | High-strength imported high-quality aluminum alloy |
| Maximum load | 10kg |
| Peak acceleration | 20—2000 G |
| Pulse duration | 0.2—18ms |
| Equipment size | 660 × 700 × 2380mm |
| Equipment weight | 820 kg |
| Measuring System |
| Input channel | 2 channels |
| Sampling frequency | 192KHz |
| Input form | Voltage, Electric Charge |
| Voltage range | -10v--+10v |
| Coupling method | AC, DC, ICP |
| Shock waveform | Half Sine |
| Communication interface | USB2.0 |
| Support standard | National standard, national military standard, U.S. military
standard, user-defined standard |
| Operating system | Microsoft Windows7/10 |
| System Acceleration Sensor |
| Brand | YMC |
| Output method | Charge type |
| Sensitivity | 3.93pC/g |
| Frequency range | 0.5—12KHz |
| Acceleration range | ±2500G |
| Working environment | -40~+160℃ |
| Other Instructions |
| Power supply | Single phase 220V±10% |
| Compressed air | 0.5—0.8Mpa |
| Temperature | RT～40℃ |
| Humidity | 25℃＜85RH％ |
Use Environment:
1. Site temperature: 5℃~+28℃ (average temperature within 24 hours
≤28℃);
2. Relative humidity: ≤85%RH;
3. Air source: 0.5-- 0.8MPa
4. Power supply conditions: single-phase three-line;
5. Voltage input: AC220V;
6. Allowable frequency fluctuation range :(50±0.5) Hz;
7. The grounding resistance of the PGND cable is less than 4 Ω.
8. Please configure an air or power switch of corresponding
capacity (100A) for the device at the installation site, and this
switch is used independently for the device.
