| AC Hipot test |
| Booster rated output capacity | 500VA (5000V/100mA), short circuit current is greater than 200mA |
| Output voltage waveform, distortion, adjustment rate | Sine wave, <3% (pure resistance,5000V/1mA), <3% (from empty
load to full load) |
| Output voltage setting | Range | 500～5000V |
| Resolution, accuracy | 5V,±(3%×setting+10V) |
| Frequency setting | Range, accuracy | 50Hz/60Hz, ±0.1%×setting |
| Alarming limits setting | Current upper-limit | 0.10~99.99mA |
| Current lower-limit | 0.00~10.00mA |
| Compensation current setting | Range | 0.00~10.00mA, automatic testing, compensation can be set to ON/OFF |
| Time setting | Range | 1~999s |
| Ramp up time range | 1~100s |
| Accuracy | ±(0.1%×setting+1count) |
| Breakdown current alarm | Range, accuracy | 0.10~99.99mA, ±(3%×reading+3counts) |
| Insulation Resistance test |
| Rated output capacity | 2VA(1000V/2mA) |
| Output voltage regulation, output voltage ripple |
<3%(From no load to full load), <1% |
| Output voltage setting | Range, accuracy | DC 500V or 1000V, ±(3%×setting+3counts) |
| Alarming limits setting | Resistance upper-limit range | 0.0~99.9 MΩ,100~2000MΩ(If upper-limit is set to 0, it will not make
adjudgment for upper limit) |
| Resistance lower-limit range | 0.3~99.9 MΩ, 100~2000MΩ |
| Time setting | Range, accuracy | 1~999s, ±(0.1%×setting+1count) |
| Insulation resistance measurement | Range | 0.0~99.9 MΩ, 100~2000 MΩ |
| Accuracy | ≤200MΩ: ±(3%×reading+3counts) >200MΩ:±(8%×reading+8counts) |
| Ground Bond Resistance test |
| No load output voltage | <12V |
| Output current setting | Range, accuracy | 3~30A, ±(3%×setting+0.2A) |
| Current frequency setting | Range, accuracy | Sine waveform 50Hz/60Hz, ±0.1%×setting |
| Test time setting | Range | 1~999s |
| Accuracy | ±(0.1%×setting+1count) |
| Result display mode | Ground resistance or voltage |
| Ground resistance display mode |
| Alarming limits setting | Resistance upper-limit range | 3A ≤ output current ≤ 10A:10~600 mΩ 11A ≤ output current ≤ 25A:10~300 mΩ 26A ≤ output current ≤ 30A:10~200 mΩ |
| Resistance lower-limit range | 0~100 mΩ |
| Compensation resistance setting | Range | 0~200 mΩ, automatic testing, compensation can be set to ON/OFF |
| Ground bond resistance measurement | Range, accuracy | 10~600 mΩ, ±(3%×reading+ 5counts) |
| Ground voltage display mode |
| Alarming limits setting | Voltage upper-limit range | 30~7500 mV |
| Voltage lower-limit range | 0~3000 mV |
| Compensation voltage setting | Range | 0~1000 mV, automatic testing, compensation can be set to ON/OFF |
| Ground bond resistance measurement | Range, accuracy | 10~7500 mV, ±(3%×reading+ 50mV) |
| Leakage Current test |
| Leakage current test type setting | Single phase load, static/dynamic leakage current |
| MD network selection | Standard IEC 60990 figure 4 network; other test network optional |
| Alarming limits Setting | Current upper-limit range | 0.050~9.999mA |
| Current lower-limit range | 0.000~5.000mA |
| Leakage current compensation setting | Range | 0.000~1.000mA, automatic testing, compensation can be set to ON/OFF |
| Time test setting | Range, accuracy | 1~999s, ±(0.1%×setting+1count) |
| Leakage current measurement | Range | 0.050~9.999mA |
| Accuracy | DC~10kHz: ± (3%×reading+0.010mA) 10 kHz ~1MHz: ± (5%×reading+0.050mA) |
| Output voltage measurement | Range, accuracy | 60~280V(phase voltage), ±(0.5%×reading+2counts) |
| Run Power Only forAN9651S(F)/AN9651F(F)/AN9651B(F) |
| Alarming limits setting | Power upper-limit range | 6~6000W |
| Power lower-limit range | 0~6000W |
| Test time setting | Range, accuracy | 1~999s, ±(0.1%×setting+1count) |
| Voltage measurement | Range, accuracy | 60~280V (phase voltage), ±(0.5%×reading+2counts) |
| Current measurement | Range, accuracy | 0.030~3.999A, 4.00~25.00A, ±(0.5%×reading+2counts) |
| Active power measurement | Range, accuracy | 30.0~199.9W: ±(0.5%×reading+5W), 200~6000W(or2000W): ±(0.5%×reading+30W) |
| Power factor measurement | Range, accuracy | 0.10~1.00, ±(2%×reading+2 counts) |
| Low voltage start test |
| Alarming limits setting | Current upper-limit range | 0.30~25.00A |
| Current lower-limit range | 0.00~25.00A |
| Test time setting | Range, accuracy | 1~999s, ±(0.1%×setting +0.05s) |
| Voltage measurement | Range, accuracy | 60~280V (phase voltage), ±(0.5%×reading+2counts) |
| Current measurement | Range, accuracy | 0.030~3.999A, 4.00~25.00A, ±(0.5%×reading+2counts) |
| Power supply for UUT |
| SN2212B Built-in isolation transformer |
| Isolation transformer input voltage, frequency | Determined based on input voltage and frequency |
| Isolation transformer output voltage ratio | Leakage current test | The output voltage is 1.06 times the input voltage |
| Run power test | The output voltage is 1.00 times the input voltage |
| Low voltage start test | The output voltage is 0.85 times the input voltage |
| Isolation transformer capacity | Single phase load rated capacity 6000VA |
| Isolation transformer voltage regulation | 3% (from no load to full load) |
| Overcurrent protection | Maximum current is 30A, automatically cut off the isolated power
supply after 5s overcurrent |
| SN2212S, SN2212F Built-in variable frequency power supply |
| Max. output capacity | 5000VA |
| Output voltage distortion | 1% @ 47~63Hz |
| Output voltage stability | 1% |
| Programmed output voltage | Voltage range | 0~300V |
| Voltage accuracy | 0.5%RD+0.5%F.S. |
| Programmed output frequency | Frequency Range | 47~63Hz |
| Frequency stability | 0.1% |
| Output maximum current | 0~150V file | 27A |
| 0~300V file | 14A |
| SN2212S Configured IN-Pad |
| Processor | ARM926 core, 400MHz frequency |
| Operating system | Windows CE |
| Software | ESRS-Pad special software for safety test |
| Display | 10.4” TFT color LCD |
| Operation method | Input through touch screen, support input through USB interface
mouse and keyboard |
| Storage | 50MB FLASH, user can choose large capacity SD memory card |
| External Interface | 2-way RS232 interface, 2-way USB interface, CAN interface, DC12V
power interface |
| Mounting brackets | 3D, full angle, display stand |
| Bar code scanner | One barcode scanner with an RS232 interface defaulted |
| Interface function |
| Remote control interface | Standard, standard foot switch (start) |
| Alarm light interface | Standard, standard three-color warning light (test, qualified,
warning) |
| Communication Interface | Standard RSA32, optional RS485, network port, GPIB, etc. |
| Variable frequency power control interface | Optional |
| Switch interface | Optional, start, stop, test, pass, alarm switch output |
| Printer interface | Optional, support for dot matrix printers and micro printers |
| General specification |
| Verification and calibration environment | 23 ° C ± 5 ° C, (45 ~ 75)% RH, less dust |
| Use environment | 0 ° C ± 40 ° C, (5 ~ 90)% RH, less dust |
| Storage environment | -10 ° C ~ 55 ° C, (5 ~ 95)% RH, less dust |
| System power | 220V±10%, 50Hz±5%, 10A |
| System power consumption | Maximum 1000VA (excluding the operating power consumption of the
tested product) |
| System weight (without packaging) | About 80kg |
| Dimensions (mm, without packaging) | SN2212S | 483(W)x 600(D)x 1355(H) |
| SN2212F | 483(W)x 600(D)x 1355(H) |
| SN2212B | 530(W)x 460(D)x 1105(H) |
